LEDGlow Smartphone Underbody Kit with Bluetooth Control

INSTALLATION GUIDE 1.877.LED.GLOW • LEDGLOW.COM

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 1 INSTALLATION GUIDE WARNING: DO NOT USE THIS APP OR YOUR MOBILE PHONE WHILE OPERATING A MOTOR VEHICLE. THIS PRODUCT IS DESIGNED FOR OFF ROAD USE ONLY. PLEASE CHECK YOUR LOCAL AND STATE LAWS FOR THE PROPER USE OF THIS PRODUCT BEFORE INSTALLATION, AS EVERY STATE HAS DIFFERENT POLICIES AND PROCEDURES REGARDING AFTERMARKET LED LIGHTING ACCESSORIES. LEDGLOW IS NOT RESPONSIBLE FOR ANY FINES THAT YOU MAY RECEIVE WHILE USING THIS LIGHTING KIT. IT IS RECOMMENDED THAT THIS KIT BE INSTALLED BY A LICENSED PROFESSIONAL. IMPROPER INSTALLATION OF THIS KIT WILL VOID ALL WARRANTIES. PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED UNDERBODY KIT. This is a comprehensive installation guide including instructions for the 4 pc Million Color SMD LED Underbody Lighting Kit with Smartphone Control along with optional add-on kits. Add-On Kits such as Truck Add-On Tubes, Interior Lights, Grille Light, Wheel Well Lights, and Display Module may be purchased separately at www.LEDGlow.com. Please feel free to skip portions of this guide that are not relevant to your specific application. The 4pc Million Color SMD LED Underbody Lighting Kit with Smartphone Control and any optional add-on kits include: UNDERBODY: • (2) 30” SMD Underbody Tubes • (2) 46” SMD Underbody Tubes • Water-Resistant Control Box • 7 Port Underbody Tube Distributor Cable • Tube Brackets • Zip-ties • Screws • Display Module (Optional) OPTIONAL TRUCK ADD-ON: • (2) 24” SMD Truck Underbody Tubes • Tube Brackets • Zip-ties • Screws OPTIONAL GRILLE ADD-ON: OPTIONAL WHEEL WELL ADD-ON: OPTIONAL INTERIOR ADD-ON: • 24” SMD Grille Tube • Tube Brackets • Zip-ties • Screws • (4) 24” Flexible SMD Wheel Well Tubes • Wheel Well Distributor Cable • Zip-ties • Screws • Up to (6) 12” SMD Interior Tubes • Interior Distributor Cable • Tube Brackets • Zip-ties • Screws • 3M™ Tape

2 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE 1. Arrange the underbody tubes as they would be placed on the vehicle. For proper placement of tubes, refer to section 3. 2. If purchased, arrange the truck, wheel well, grille, and interior add-on tubes as they would be placed on the vehicle. For proper placement of add-on tubes, refer to sections 4-7. 3. Plug all underbody tube wires into the provided distributor cable. 4. If purchased, plug all wheel well tube wires into the wheel well tube distributor cable. Plug the front wheel well tubes into the ports labeled “F” and the rear wheel well tubes into the ports labeled “R.” 5. If purchased, plug all interior tube wires into the interior tube distributor cable. 6. If purchased, plug the Display Module into the port on the control box labeled “DISPLAY”. 7. Plug the underbody tube distributor cable into the port on the control box labeled “UNDERBODY.” 8. If purchased, plug the cable of the wheel well tube distributor cable into the port on the control box labeled “WHEEL WELL.” 9. If purchased, plug the interior tube distributor cable into the port on the control box labeled “INTERIOR.” 10. Temporarily power your kit with any 12 volt source to ensure it is functioning properly before moving forward with the installation. Simply connect the red wire from the control box to a positive 12 volt source and connect the black wire to any good ground source. Confirm all light tubes illuminate and pair the control box to your device following the steps in section 2. 11. Once the kit has been confirmed to be working properly, disconnect it from its power source and make all components available for installation. Section 1: How to Test Your Kit

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 3 INSTALLATION GUIDE Section 2: Pairing the Kit to Your Device Android Device Pairing Instructions (Android 4.4 & Up Required): LEDGlow Automotive Control App: 1. Open the Google Play Store. 2. Type in “LEDGlow Automotive Control” into the Google Play Store search bar. 3. Download and install the LEDGlow Automotive Control app. 4. Confirm location services are enabled if you are using Android 4.4 or higher. To enable locations services, go to Phone Settings > Location > On. Restart the app if location services were disabled after installing the LEDGlow Automotive Control app. 5. Open the LEDGlow Automotive Control app. 6. Power the control box using a 12 volt source. If the LED status indicator light on the control box is yellow, it is ready to be paired with the LEDGlow Automotive Control app. The status indicator light on the control box will turn green when the control box is finished pairing. 7. If the LED status indicator light is red, disconnect power from the control box, then reconnect power. When power is reconnected, the LED status indicator light will turn yellow, indicating the control box is ready to be paired to the app. The status indicator light will turn green when it is finished pairing with the app. LEDGlow Automotive Control App: Apple Device Pairing Instructions (iOS 9.1 & Up Required): 1. Open the iOS App Store. 2. Search the iOS App Store for “LEDGlow Automotive Control” by typing it into the search bar. 3. Download the LEDGlow Automotive Control app and install it on your iOS device. 4. Open the LEDGlow Automotive Control app. 5. Power the control box using a 12 volt source. If the LED status indicator light on the control box is yellow, it is ready to be paired with the LEDGlow Automotive Control app. The status indicator light on the control box will turn green when the control box is finished pairing. 6. If the LED status indicator light is red, disconnect power from the control box, then reconnect power. When power is reconnected, the LED status indicator light will turn yellow, indicating the control box is ready to be paired to the app. The status indicator light will turn green when it is finished pairing with the app.

4 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE 1. Disconnect the negative side of the vehicle’s battery. 2. Raise the vehicle (if possible). 3. Using the 30” tube with the 18’ power wire, mock up its mounting location at the rear of the vehicle. The orientation of the wire will not affect the functionality of the kit – the wire can be positioned on either side of the vehicle. However, the tube must be positioned 8-10” away from excessive heat or moving parts. 4. Mock up the remaining 30” tube to the front of the vehicle 8-10” away from excessive heat or moving parts. Much like the rear underbody tube, the orientation of the wire will not affect the functionality of the kit – the wire can be positioned on either side of the vehicle. If a Grille Add-on Kit was also purchased, refer to Section 6 to mount the additional 24” tube that came with the Grille Add-on kit. 5. Mock up the (2) 46” tubes on both of the vehicle’s sides. Face the power wires of the 46” side underbody tubes toward the vehicle’s rear, making sure to place the tubes 8-10” away from excessive heat or moving parts. If a Truck Add-on Kit was also purchased, refer to Section 4 on page 5 to mount the additional 24” tubes that came with the Truck Add-on kit. 6. Mark drill locations for the mounting brackets on a level surface facing inward or outward, depending on tube placement preference. Use a 7/64” drill bit to drill pilot holes in the mounting bracket locations and attach the brackets to the vehicle using the included screws. We recommend using 2-3 brackets per tube for 24” and 30” tubes, and 3-4 brackets for 46” tubes. 7. Peel any clear film off of the underbody tubes. 8. Snap the 30” underbody tube with the 18’ power wire into the rear mounting brackets. Snap the other ” tube into the front mounting brackets. Snap the (2) 46” underbody tubes into the side mounting brackets and secure all tubes into the brackets with the included zip-ties. Refer to sections 4-7 for additional details on optional truck, wheel well, grille, and interior add-on tube installation instructions. If no add-on kits were purchased, skip to Section 8. Section 3: Underbody Tube Installation

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 5 INSTALLATION GUIDE Section 5: Wheel Well Add-On Tube Installation (Optional) 1. (Optional) Remove the vehicle’s wheels for better access to the wheel well mounting locations. 2. Before mounting the wheel well tubes, ensure that all four tubes will be positioned 8-10” away from excessive heat or any moving parts. When mounting the tubes, ensure the power wires are facing the front of the vehicle. 3. Mount the 24” driver’s side tube either behind the wheel strut facing toward the wheel or inside of the inner fender well by using the included self-tapping screws. The 24” wheel well tubes are flexible and can be contoured easily for precise positioning. Repeat this step for the remaining (3) 24” wheel well tubes, keeping their placement consistent with the driver’s side tube installation. 4. Reinstall your vehicle’s wheels if they were removed in accordance to factory specifications. 5. Test the clearance of the wheel well tubes by moving the steering wheel back and forth to confirm that the tubes do not interfere with the wheels in any way. Section 4: Truck Add-On Tube Installation (Optional) 1. Before mounting the truck add-on tubes, ensure that both 24” tubes will be positioned 8-10” away from excessive heat or any moving parts. When mounting the tubes, ensure the power wires are facing the vehicle’s rear. The tubes should be mounted behind the driver and passenger side underbody tubes to cover major gaps between the side and rear tubes. 2. Mark drill locations for the mounting brackets on a level surface. Use a 7/64” drill bit to drill pilot holes for the mounting brackets and install the mounting brackets with the included screws through the pilot holes. We recommend using 2-3 brackets per tube. 3. Peel any clear film off of the underbody truck tubes. 4. Snap the (2) 24” underbody tubes into the mounting brackets and secure them in place using the included zip-ties. Section 6: Grille Add-On Tube Installation (Optional) 1. Lower the vehicle (if previously raised). 2. Arrange the grille tube in the desired location behind the vehicle’s grille, positioning it 8-10” away from excessive heat or moving parts. The orientation of the grille tube’s power wire should match that of the installed front underbody tube. For example, if the front underbody tube’s power wire is on the passenger’s side of the vehicle, the grille tube’s power wire should also be on the passenger’s side of the vehicle. 3. Peel any clear film off of the grille tube. 4. Use the included mounting brackets and screws to secure the tube behind the vehicle’s grille, securing the tube in place using the included zip-ties. Take care not to screw the brackets into the radiator, AC condenser, any sensors, or other vital engine components in this part of the vehicle.

6 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE 1. Determine the desired location of the interior tubes, ensuring that the power wires are not near the seat rails so that they do not get pinched. Recommended interior tube placements include under the dashboard, under the front seats, and under the rear seats. Note: The orientation of the interior tube power wires will not impact installation, allowing for versatile mounting options. 2. Clean any dirt, oil, or dust from the surface of each mounting location using an alcohol prep pad (not included). 3. Using 3M™ tape and screws, mount the interior tube brackets to your preferred mounting locations and snap the interior tubes into the brackets. Mount the tubes securely. If mounting tubes under the dashboard, keep the tubes and wires away from the pedals. Use the included zip-ties to mount the tubes if they cannot be mounted to a flat location using brackets. 4. Wires can be hidden in a variety of ways according to preference. Options include removing trim panels and securing the wires with zip-ties. Please remove and replace trim per factory specification. Wires may also be hidden under seats or under the vehicle’s carpet. We suggest routing wires alongside factory wiring harnesses. Section 7: Interior Add-On Tube Installation (Optional) Section 8: Routing the Wires 1. Inspect your vehicle’s engine bay for available openings to mount the water-resistant control box, underbody tube distributor cable, and wheel well tube distributor cable (if purchased). Ensure that the location of the control box allows access and reach for all distributor cables to plug in properly. Plan to place the control box and distributor cable(s) in the driest possible part of the engine bay away from excessive heat or any moving parts. 2. Raise the vehicle (if possible). 3. Beginning at the back of the vehicle, route the wires from all installed light tubes toward the location of the control box in the engine bay, keeping the wires clear of excessive heat and any moving parts. Bind any excess power wire lengths from tubes tightly and secure with zip-ties, but avoid over-tightening them so that they do not splice open, which will void all warranties. 4. Plug the wires for all underbody tubes into the included distributor cable. 5. If wheel well lights are installed, plug the wires from the wheel well tubes into the wheel well tube distributor cable. Plug the front wheel well tubes into the ports labeled “F” and plug the rear wheel well tubes into the ports labeled “R.” 6. Lower the vehicle (if it was raised). 7. Mount the control box inside the engine bay using 3M™ tape and screws, ensuring that the LEDGlow logo is facing upright. Mount the underbody and optional wheel well tube distributor cables in their determined locations with 3M™ tape and screws. Use caution when using screws to confirm no vital engine components are damaged. 8. If you purchased the optional Display Module, route its wire from inside the vehicle through the firewall with a grommet in place. Plug the Display Module wire into the port on the control box labeled “DISPLAY.” 9. If interior lights have been installed, find a safe location to mount the interior tube distributor cable inside of the vehicle away from the pedals, steering shaft, direct heat sources, and any moving parts. Recommended locations include the center console, underneath the seat, under the dashboard, or inside the glove box. Mount the interior tube distributor cable in the vehicle’s interior using 3M™ tape and screws. Run the cable from the interior tube distributor cable through the firewall with a grommet in place to the control box and plug it into the port labeled “INTERIOR.” 10. Plug the cable of the underbody distributor cable into the port on the control box labeled “UNDERBODY.” 11. Plug the cable from the optional wheel well tube distributor cable into the port on the control box labeled “WHEEL WELL.”

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 7 INSTALLATION GUIDE Optional Courtesy Light Feature Wiring Instructions: The Courtesy Light Feature will automatically change all installed lights to white, illuminating the ground around the vehicle when the doors are opened or when the dome light is activated. To utilize the optional courtesy lights feature, use a service repair manual to identify the wire used to power the dome light. Use a test light to locate the correct wire by opening and closing the vehicle’s door. Once the correct wire has been identified, disconnect the negative side of the vehicle’s battery and use a wire connector to attach the dome light wire to the white wire from the control box. When finished, reconnect the negative side of the vehicle’s battery. Please note, some vehicles have a ground-side controlled system providing constant power to the dome light, which switches the ground on and off. This can be tested with a test light or multi-meter. There will be power on both sides of the bulb when the light is off. As soon as the light turns on there will be power on one side and a ground source on the other. If this is the case in your vehicle, set the courtesy switch type to GND on the settings page of the LEDGlow Automotive Control App. If the vehicle’s dome light circuit is controlled by power and the ground never changes, set the courtesy switch type to 12V on the settings page of the LEDGlow Automotive Control App. By default, the Courtesy Light Feature is turned off in the LEDGlow Automotive Control App. Make sure to turn it on in the app’s settings page after completing the wiring steps above. Section 10: Optional Display Module Features & Installation The Display Module serves as a physical representation of how the installed underbody kit, along with any installed add-on kits, will appear on your vehicle. The Display Module mimics all settings from the Automotive Control App and replicates them via embedded LEDs throughout the surface of the Module. Replicated settings include color, patterns, and where those lights are illuminated on the vehicle. The Display Module utilizes embedded LEDs within nine specific areas to indicate light color and patterns set to the underbody, wheel well, and interior tubes. The top of the display represents the passenger side of the vehicle, while the bottom represents the driver’s side. The vertical sections at the far left and right represent the front and rear underbody tubes on the vehicle. The corners represent the wheel well tubes. The center of the Display Module features the LEDGlow logo and four buttons which control features and settings of the kit. However, when these buttons and the logo are illuminated, they also represent the color and pattern set to an installed interior kit. Section 9: Powering the Kit 1. Connect the red power wire from the control box to a positive 12 volt source. If the wires are not long enough, extend them using 16 or 18 gauge automotive-grade wire. Alternatively, the control box can be powered directly from the vehicle’s fuse box by installing LEDGlow’s Expandable Circuit, available at www.LEDGlow.com. Find more details and installation instructions for the Expandable Circuit at www.LEDGlow.com. 2. Connect the black wire from the control box to an unpainted ground source such as the grounding block, negative post on the battery, or engine ground. 3. Reconnect the negative side of the vehicle’s battery.

8 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE In addition to the display buttons, there is a music mode that will allow the lights to react to the sound of your stereo. When in music mode, the LEDGlow logo on the Display Module will be illuminated in red, regardless of the color set to the interior kit in the vehicle. The buttons on the Display Module, however, will be illuminated to reflect the specific settings applied to the interior tubes despite the activation of music mode. The Display Module features an ambient light sensor to control brightness. There is an auto-dimming feature built into the Display which automatically adjusts the brightness of the embedded lights according to its surrounding light. On a bright day, the Display Module will adjust itself by increasing its brightness for better visibility. At nighttime or in a dark setting, the Display Module will automatically dim itself. The Display Module was designed to offer multiple mounting capabilities on the interior of your vehicle. Due to its wire location, which exits from the back, the Module can easily be flush mounted on any flat surface. Additionally, there is a knock-out tab located on the bottom of the Display where the attached wire can exit. Positioning the wire in this way allows the Display to be surface mounted to the location of your choice. Please note, once the knock-out tab is removed, it cannot be replaced. To surface mount the Display Module, simply identify a mounting location, clean the location thoroughly with an alcohol prep pad, and mount the Display Module with 3M™ tape. Be sure to secure the power wire and keep it clear of the pedals and other moving parts within the vehicle. Route the wire through the firewall with a grommet in place and plug it into the port on the installed control box labeled “DISPLAY.” The four buttons on the Display Module are fully operational and are used to adjust the light kit’s settings. Detail on the function of each button can be found below: Power Button: Pressing this button will turn the kit on or off. Pressing and holding this button will turn the lights on the Display Module on or off, but the light kit will remain on. Changing Color Button: Selects from 7 solid colors: blue, green, teal, red, pink, yellow, and white. Pressing and holding this button will scroll through a million color fade but will stop when the button is released. Speed Change Button: Selects different speeds for selected patterns. Mode Button: Changes the current mode displayed. There are 16 distinct modes. Each press of the Mode Button will advance to the next mode. A complete list of modes can be found on page 12. Pressing and holding this button will turn music mode on or off. PASSENGER SIDE DRIVER SIDE Music Sensor Wheel Wells Ambient Light Sensor VEHICLE FRONT VEHICLE REAR

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 9 INSTALLATION GUIDE Section 11: App Features & Functionality If you haven’t done so already, download the LEDGlow Automotive Control app and pair your device following the steps on page 3. 1. Underbody Tab: Changes the colors and modes for the underbody lights. 2. Wheel Tab: Changes the colors and modes for the wheel well lights when unlinked. 3. Interior Tab: Changes the colors and modes for the interior lights when unlinked. 4. Settings Tab: Displays setting options within the app. 5. Power Toggle Option (For Linked Kits): Turns all of the selected kit components either on or off. 6. Link/Unlink: While linked, the system can run as one unit and all features will function together across all components. When unlinked, each kit component can be independently controlled. When the link icon is highlighted, components are linked together. When the icon is greyed out, components are not linked together. 7. Color Bar: Previews the selected colors assigned to each tab. 8. Color Wheel: Use the wheel to select the colors you’d like to assign to each installed component. Up to 3 colors can be assigned to each component at one time. 9. Brightness: Adjusts the brightness of a selected color. 10. MillionColor: When set to “On” the kit will automatically scroll through every color variation available. 11. Fade: Applies a fade effect to any active mode. The fade feature can also be applied when two or more colors are selected from the color wheel, with or without a mode. 12. Speed Bar: Adjusts each mode’s rate of speed by decreasing or accelerating movement. 13. Strobe: Applies a strobe effect to any active mode. 14. Mode: Provides a drop down of 16 unique modes. See page 12 for a full list of modes and descriptions of each. 15. Music Mode: Reacts to the sound of your stereo if the optional Display Module is installed. With the Display Module installed, simply toggle the music mode to “ON” to activate this feature. 16. Preset: Provides 5 programmable and customizable preset modes. 1. 2. 3. 4. 5. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 6.

10 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE Section 12: App Settings 1. System Power: Turns the entire kit on and off. 2. Courtesy Light: Powers on the courtesy light option. 3. Courtesy Switch Type: Changes the signal output from the control box to the connection point of the white wire to be either a 12 volt positive source or a ground source to activate the courtesy light function. (Refer to page 7 for wiring instructions.) 4. Courtesy Light Color Selection: Allows you to select the color of all the lights when the white courtesy wire is triggered. Cycle the courtesy light Off/On switch to have the color options appear, once selected the color options disappear. Cycle the courtesy light Off/On switch to have the color options reappear. 5. Display Wheel Tab: Allows you to hide the wheel tab if the optional wheel well kit was not installed. 6. Display Interior Tab: Allows you to hide the interior tab if the optional interior kit was not installed. 7. Low Voltage Shut Off: Cuts the power to the kit if the vehicle’s battery voltage drops under 11 volts for two minutes. 8. Display Brightness: Controls the brightness level of the display module. This is only available if the Display Module is plugged into the control box. 9. Auto Dim Display: Enables/Disables the Display Module’s auto-dimming feature. 10. Help: Takes you to LEDGlow’s Online Support Portal. 11. Display Connected: Unlocks music mode capabilities included with the display module. If the Display is not connected, the music features are hidden and a “NO” indicator will appear. To activate music mode, connect the Display Module to the control box and toggle music mode to “ON” in the component tab for the part or part(s) of the light kit to which you would like to assign the music mode feature. 12. Reset Settings: Resets all settings back to default. 1. 2. 4. 3. 5. 6. 7. 9. 8. 10. 11.

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 11 INSTALLATION GUIDE Section 13: How to Use the App • How to Add a Single Color: Tap on the color bar until it expands into the color wheel. Select the desired color in the expanded color wheel and tap it to create a programmed color. • How to Add a Second or Third Color: On the right side of the color wheel there are three white outlined circles. Tap each of the three circles and select a color from the color wheel. • How to Remove a Second or Third Color: Expand the color wheel by tapping on the color bar if the color wheel is not already expanded. For Android users, press and hold the desired color to be removed. For iOS users, select the color you want to eliminate by pressing and holding for 2 seconds. Press the “X” to complete. • How to Link/Unlink the Wheel Well or Interior Components: Different components of the kit can be operated together or independently of each other. Linking components together will allow the same colors and patterns to be used across them. Unlinking components will allow each of them to be controlled independently. Locate the link icon on the main underbody tab, or by tapping on either the “WHEEL” or “INTERIOR” tabs. Tap the link icon ( ) once to unlink the selected section. Tap the link icon again to link them together. • How to Turn on the Million Color Mode: Million Color Mode cycles through all available colors. To turn it on or off, tap on the color bar to expand the color wheel. Use the toggle option to turn the Million Color Mode either on or off. Program the Million Color Mode on a selected component or assign this mode to all available components. • How to Turn on the Fade Mode: Expand the color wheel by tapping on the color bar. After the color wheel is expanded, utilize the available toggle option to turn the fade mode on or off for integrating a fading transition to selected kit areas. • How to Change the Speed on a Mode: Program more than one color on the app and slide the speed bar to adjust the color transition and/or mode. • How to Turn on the Strobe Mode: Locate the strobe toggle located above the mode bar near the bottom of the app screen. Slide the white circle on the strobe bar to on or off to integrate a white strobing effect into any mode. • How to Change the Brightness: Check the app screen to verify that the color wheel is expanded. Tapping the color bar will expand the color wheel if needed. Locate the brightness bar under the color wheel. Use the slider to decrease or increase color brightness. • How to Change a Mode: Scroll to the bottom of the page and tap on “mode.” Tap on the list to select a mode. • How to Turn on the Courtesy Lights: Press the settings tab ( ). Find the Courtesy Light Feature section and set it to “on” by sliding the toggle. • How to Change 12V or GND for Courtesy Lights: Press the settings tab ( ). Once in settings, you will see the option to toggle between 12V and GND. If your vehicle has a ground side controlled system with constant power to the dome light, have the courtesy switch type set to GND. If your vehicle’s dome light circuit is controlled by power and the ground never changes, have the courtesy switch type set to 12V. See page 7 for more details. • How to Hide the Wheel Well Tab: Press the settings tab ( ) and toggle the wheel well tab to “off.” • How to Hide the Interior Tab: Press the settings tab ( ) and toggle the interior tab to “off.” • How to Save a Preset: Determine the mode and color choices desired to save as a preset. For Android users, press and hold down for 2 seconds on the selected preset number, which will prompt a confirmation message on the screen indicating that the preset has been saved. For iOS users, press and hold down on the desired preset number to save and press “OK” after the popup notification appears. • How to Reset the App: Go to the settings tab ( ) and tap on “Reset Settings.” This will reset all settings back to default.

12 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE Section 14: Functionality • Solid: Sets the kit to a solid color chosen from the color wheel. If more than one color is selected, the color will switch instantly to the next. • Pulse: Gradually fades the light then flashes back on in a pulse effect. • Sweeping: Lights up the entire front of the kit and gradually runs down the sides until reaching the rear in a sweeping motion. • Kitt Scanner: Creates a scanning motion beginning at the center of the front of the kit that extends to the sides and ends at the center of the rear. • Karr Scanner: Similar to Kitt Scanner, but creates a scanning motion that begins simultaneously at the center of the front and rear tubes. The light then moves from both ends of the vehicle to the opposite ends of the vehicle, passing through each other halfway down the sides, ending at the center of the opposite ends of the vehicle. • Chase: Gradually lights up the entire front section of the kit, then trickles down the sides until reaching the rear tube in a chase pattern. • Color Chase: Creates a chasing effect that starts in the front of the kit, reaches the rear, and then meets back again in the center of the sides. This mode works best with two or more colors selected. • Chase vs Chase: Creates a chasing effect from both the front and rear, crossing each other in the center of the sides. This mode works best with two or more colors selected. • Progression: Lights up the front entirely along with select parts of the sides as they scan front to back until reaching the rear. • Running Color: Creates a scanning color effect on top of a solid color. • Flash: Flashes all lights simultaneously. • Wig Wag: Lights up the front and rear simultaneously. After the front and rear illuminate, both of the sides light up simultaneously. • Solid Zone: Flashes solid sections of the front and back while the sides flash simultaneously. • Section Pulse: Creates a pulse effect that cycles through the kit. • Light Show: Creates a scanning effect that cycles through the kit and then stops and flashes. Once it is finished flashing, it begins scanning again. • Equalizer: Starting at the center of the front tube, solid light radiates outward, extending to the side tubes, then to the rear tube, illuminating the rear tube from the outside ends to the center, eventually lighting all of the tubes simultaneously. The pattern then moves back to the front of the vehicle in reverse, shutting off the lights as it radiates back to the center of the front tube. The names, order, and descriptions of the modes are:

Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com 13 INSTALLATION GUIDE Section 15: Tips & Troubleshooting • The LEDGlow Automotive Control App will not disconnect while multitasking between other apps or phone features. Force-closing the app will not automatically shut down the kit. • Shut down the app by double-tapping your mobile device’s “back” button when utilizing the app. • Pairing will automatically occur after the initial app setup, as long as Bluetooth is turned on in the iOS or Android app settings and the controller is fully powered. • If the Android or iOS device cannot connect to the controller, try one of the following steps and then reopen the LEDGlow Automotive Control app: a. Restart or select the power cycle option on any Android or iOS device. b. Restart your Bluetooth-enabled control box by disconnecting its power for 20 seconds, reconnect power, and test the kit for proper functionality.

14 Tech Support 856.768.5700 Ext.2 • TechSupport@LEDGlow.com INSTALLATION GUIDE TERMS AND CONDITIONS 1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP, WRITTEN NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY PERIOD. THE SPECIFIC WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER. 2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER’S EXCLUSIVE REMEDY AND LEDGLOW’S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR) ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER’S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER OF ALL CLAIMS THERETO. 3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO ANY OF THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN THE USER’S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL, OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT’S ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS SOLD AS IS AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND BATTERIES. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. THIS LIMITED WARRANTY IS SUBJECT TO ALL OF THE FOLLOWING TERMS AND CONDITIONS: PROOF OF PURCHASE; REGISTRATION: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty. DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE. LIMITATION OF LIABILITY THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER. GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty. This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full determination of rights. iPhone®, iPod®, iPad® and iTunes® are registered trademarks of Apple Inc., registered in the U.S. and other countries. Android™ is a registered trademark of Google, Inc, registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. Bluetooth® is a registered trademark of Bluetooth SIG, Inc. App Store is a service mark of Apple Inc.

Free Lifetime Technical Support Same Day Shipping on Orders Placed By 3PM Eastern 1 Year Limited Warranty 1.877.LED.GLOW • LEDGLOW.COM 444 COMMERCE LANE SUITE B, WEST BERLIN, NJ 08091 LEDGLOW LIGHTING, LLC

RkJQdWJsaXNoZXIy MTIxODAy