1 LEDGlow Lighting, LLC • LEDGlow.com Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com ® I N S T A L L A T I O N G U I D E 1 . 877 . LED.GLOW • LEDGLOW.COM
1 LEDGlow Lighting, LLC • LEDGlow.com Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com ® I N S T A L L A T I O N G U I D E WARNING: THIS PRODUCT IS DESIGNED FOR OFF ROAD USE ONLY. PLEASE CHECK YOUR LOCAL AND STATE LAWS FOR THE PROPER USE OF THIS PRODUCT. Every state has different policies and procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may receive while using this lighting kit. Note: We recommend using a licensed professional to install this lighting kit. The improper installation of this kit will void all warranties. We recommend installing each lighting strip using Adhesion Promoter, which allows for a much stronger bond between the adhesive tape of the light strip and the cleaned mounting surface of your Ryker. PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED RYKER KIT. RYKER LIGHTING KIT INCLUDES: • Advanced Million Color Control Box • (4) 24” Strips • (2) 4” Strips • (1) 6pc Power Harness • (2) 18” Strips • Alcohol Pads • (2) 6pc Add-On Harnesses • (1) 10” Strip • Promoter • (1) 4pc Add-On Harness • (5) 8” Strips • Zip Ties • (1) 2pc Add-On Harness • (2) 8” Inverted Strips • Double-Sided Tape for Control Box • (2) 3' Extensions • (4) 6” Strips • (2) Crimp-on Ring Terminals 1. Upon receiving your newRyker lighting kit, we ask that you first test the kit to ensure it is functioning correctly. Plug the male connections from the strips and control box into the female connections of the harness. Connect the red power wire to the positive terminal of the battery and the black groundwire to the negative terminal of the battery. Once the wires are temporarily secure, power the kit to ensure full functionality before installing it. If everything appears to be working correctly, turn the kit off and disconnect the power and groundwires from the battery to prepare for installation. 2. Remove any plastic panels that will be in your way startingwith the hood, headlight trim, fuel tank trim, air cleaner and side panels, most of which are held inwith push clips. 3. Be sure to clean all of themounting areas with alcohol prep pads and apply adhesion promoter to the cleaned areas. RYKER CONTROL BOX WIRING: Red Wire Black Wire Blue Wire +12v Ground Optional Brake Light Control
2 LEDGlow Lighting, LLC • LEDGlow.com Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com ® I N S T A L L A T I O N G U I D E Note: The strips can be mounted in any area that isn’t hot or near moving parts. 4. Recommendedmounting locations: • (2) 6” strips on the undertail • (2) 6” strips on the frame tubing under the seat • (2) 8” strips on the lower frame rail behind the foot peg, 1 on each side • (4) 24” strips around the engine with 2 on each side, 1 shining upward and 1 shining downward • (2) inverted 8” strips go on the headlights so that the LED’s face downward into each headlight • (1) 18” strip on the underside of the swing arm • (1) 8” strip under the gas tank • (1) 10” strip on the support in the engine bay keeping clear of the steering components • (1) 18” strip on the inside of the front bumper shining upward behind the front grille • (2) 8” strips on the rear bar of the upper control arms shining downward, 1 on each side • (2) 4” strips on the lower control arms shining downward, 1 on each side 5. Attach the strips by pressing firmly onto the suggested mounting locations. Secure with zip ties when able. 6. Using the 4pc add-on harness, connect the (2) 6” strips under the tail, (2) 6” strips under the seat and the 8” strip under the gas tank and run the harness lead to the front of the Ryker. 7. Using a 6pc add-on harness, connect the (2) 24” strips around the engine bay on the right side, the 8” strip behind the right foot peg, the 8” and 4” strips on the right front control arms, and the inverted 8” strip on the right headlight and run the harness lead to the front of the Ryker. 8. Using a 6pc add-on harness, connect the 18” strip on the swing arm, (2) 24” strips around the engine bay on the left side, the 8” strip behind the left foot peg, the 8” and 4” strips on the left front control arms, and the inverted 8” strip on the left headlight and run the harness lead to the front of the Ryker. 9. Using the 6pc power harness, connect the (3) add-on harnesses that were run to the front of the bike, the 10” strip in the engine bay and the 18” grille light and connect to the control box. 10. Using an alcohol prep pad, clean an area on the battery in order tomount the control box using double sided tape. 11. Be sure to secure all the wires using zip ties. 12. Attach ring terminal connectors to the red and black wires from the control box and connect them to the positive and negative posts on the battery. 13. Using a test light, locate the white brake light signal wire on the left side of the Ryker that has 12 volts when the brakes are applied. Using the supplied clamp-on wire connector, connect the blue wire from the control box using a 16-18ga automotive grade wire to extend if needed. The brake light feature will illuminate all the strips red anytime the brakes are pressed, whether the kit is on or off. 14. Wireless Remote Functions: This kit provides multiple lighting patterns and several brightness levels, which are easily operated using the includedwireless remote. The remote consists of four buttons, “A, B, C, D.” • Button A: Cycles through 15 solid colors as well as a color cycle and a color fade pattern. • Hold for 5 seconds to select brightness level when on a solid color. • Button B: Activates strobing patternwhen a single color is selected. • Hold to increase pattern speedwhen on color cycle/ color fade pattern. • Button C: Activates fading patternwhen a single color is selected. • Hold to decrease pattern speedwhen on color cycle/ color fade pattern. • Button D : Power On/Off. 15. Reprogramming theWireless Remote: This procedure is going to be used for programming an existing or a brand newwireless remote to the control box. If the control box is currently connected to power and ground, please disconnect the groundwire from the ground source. Reconnect the groundwire back to the ground source, and once this is connected, the lights on the strips will turn on green. Within 5 seconds fromwhen the kit turns on green, you can then press the A and then the B button on the wireless remote. If this programming is successful, the light strips will flicker green twice, and the kit will remain powered on. If the remote is not controlling the system, please repeat the steps above.
3 LEDGlow Lighting, LLC • LEDGlow.com Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com ® I N S T A L L A T I O N G U I D E 24” Strip 8” Inverted Strip 18” Strip 6” Strip 8” Strip 18” Strip 8” Inverted Strip 10” Strip 4” Strip 8” Strip
4 LEDGlow Lighting, LLC • LEDGlow.com Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com ® I N S T A L L A T I O N G U I D E TERMS AND CONDITIONS 1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP, WRITTEN NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY PERIOD. THE SPECIFIC WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER. 2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER’S EXCLUSIVE REMEDY AND LEDGLOW’S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR) ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOWWILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER’S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER OF ALL CLAIMS THERETO. 3. EXCEPTIONS TO LIMITEDWARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO ANY OF THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN THE USER’S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL, OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT’S ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROMWARRANTY COVERAGE PRODUCTS SOLD AS IS AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROMWARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND BATTERIES. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. THIS LIMITED WARRANTY IS SUBJECT TO ALL OF THE FOLLOWING TERMS AND CONDITIONS: PROOF OF PURCHASE; REGISTRATION: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty. DISCLAIMER OFWARRANTY EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE. LIMITATION OF LIABILITY THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER. GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty. This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full determination of rights.
I N S T A L L A T I O N G U I D E LEDGLOW L IGHT I NG, LLC • 1 . 877 . LED.GLOW • LEDGLOW.COM 444 COMMERCE LANE SU I TE B, WEST BERL I N, NJ 08091 05/22 Free Lifetime Technical Support Same Day Shipping on Orders Placed By 3PM Eastern 1 Year Limited Warranty ® RYKER® IS A REGISTERED TRADEMARK OF BOMBARDIER RECREATIONAL PRODUCTS INC. THIS PRODUCT IS NOT DESIGNED, PRODUCED OR MANUFACTURED BY BOMBARDIER RECREATIONAL PRODUCTS INC. LEDGLOW LIGHTING, LLC IS NOT IN ANY WAY, SHAPE OR FORM AFFILIATED WITH BOMBARDIER RECREATIONAL PRODUCTS INC.
RkJQdWJsaXNoZXIy MTIxODAy